SpeedyBee F7 V3 flight controller

 BLE Bluetooth:
 Supported. Used for flight controller configuration and has a built-in 2.4GHz Wi-Fi and Bluetooth combo chip.

 Flash FC firmware wirelessly:
 Supported. Please go to MENU > FC Firmware Flasher

 Download/analyze Blackbox:
 Supported. Please go to MENU > Blackbox Analyzer

 Connection option for DJI air unit:
 Two options are supported: 6-pin connector or direct soldering.

 6-pin DJI Air Unit connector:
 Supported. Fully compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no need to change cables.

 Flash (for BlackBox):
 500MB

 BetaFlight Camera Control Pad:
 Yes (CC pad on the front)

 Power consumption:
 3S - 6S LiPo

 3.3V output:
 Supported. Designed for receivers with 3.3V input. Up to 500mA current load.

 4.5V output:
 Supported. Designed for receiver and GPS module even when the FC is powered via USB port. Up to 1A current load.

 5V output:
 10 groups of 5V outputs, three +5V pads and 1 BZ+ pad (for the buzzer) on the front panel, and 6 +5V outputs in the connectors on the bottom panel. The total current load is 2A.

 9V output:
 2 groups of 9V outputs, one +9V pad on the front and another in a connector on the bottom. Total current load is 4A.

 ESC signal:
 M1 - M4 on the bottom and M5-M8 on the front.

 UART:
 5 sets (UART1, UART2, UART3, UART4 (for ESC telemetry), UART6)

 ESC telemetry:
 R4(UART4)

 I2C:
 Supported. SDA and SCL pads on the front. Used for magnetometer, sonar, etc.

 LED pad:
 Used for WS2812 LEDs controlled by Betaflight firmware.

 Summer:
 BZ+ and BZ- pads are used for 5V buzzer

 BOOT button:
 Supports.
 A: If you hold down the BOOT button and turn on the FC at the same time, it will force the FC to enter DFU mode. This is for flashing the firmware if the FC breaks.

 B: When the FC is powered on and in standby mode, the BOOT button can control the LED strips connected to the LED1-LED4 connectors on the bottom. By default, short press the BOOT button to switch the LED display mode. Long press the BOOT button to switch between SpeedyBee LED mode and BF LED mode. In BF LED mode, all LED1-LED4 strips are controlled by the Betaflight firmware.

 Scope of delivery:
 1x SpeedyBee F7 V3 flight controller
 1x DJI 6-pin cable (80mm)
 1x SH 1.0mm 25mm long 8-pin cable (for FC-ESC connection)
 1x M3x8mm silicone grommets (for FC)
 1x 4-pin SH1.0 to 3+2-pin JST1.25 FPV Cam Cable (30mm)
 1x 4-pin SH1.0 to 3+2-pin JST1.25 FPV Cam Cable (60mm)
 1x 4-pin SH1.0 to 4-pin JST1.25 FPV Cam Cable (60mm)
 1x 4-pin SH1.0 radio receiver cable (100 mm)
 1x 4-pin SH1.0 to 4-pin SH1.0 Analog VTX Cable
 1x 6-pin SH1.0 GPS module cable without connector at the other end (100 mm)
 1x 6-pin SH1.0 GPS module cable with connector at the other end